Makita 40V Max Brushless 6 Piece Combo 4.0Ah Kit DK0115G603

Makita 40V Max Hammer Driver Drill HP001GZ

Features:

• Drilling Modes - screwdriving mode (rotation with clutch) for achieving an even consistent finish when fastening screws. Drilling mode (rotation only) achieving 141 Nm max. torque. Hammer Drilling mode (rotation with hammering) for drilling in masonry up to a maximum 20 mm hole diameter.
• Active Feedback Sensing Technology (AFT) sensors shut down the tool in the event of a kickback providing user protection. If the bit rotation is suddenly forced to stop such as the bit jamming the motor automatically shuts down.
• Electronic Clutch - jog wheel with digital display allows for setting the selected torque quickly and easily. With 41 settings in low speed (1-45 Nm) and 21 settings in high speed (1-10 Nm).
• Mechanical speed control with an increase of the drilling speed (2,600 rpm) on both models they are able to drill 35% faster than the equivalent 18V model.
• Compact Overall Length for improved handling and control the overall length has been reduced by 23 mm vs. the 18 V equivalent.
• High Power Output - the high power 40 V max XGT Li-Ion battery allows for continuous operation in heavy duty applications such as drilling with self-feeding bit or auger bit

Makita 40V Max Impact Driver TD001GZ

Features:

• Enhanced Anvil Holder - material change from needle bearing to ball bearing provides reduction of bit wobbling. Providing more stability and control when fastening.
• Quick Change Selector - one touch mode selector located above the trigger allows the user to jump between modes single handed. Quickly changing between modes improves efficiency as you no longer have to take your hand off the tool.
• Constant Speed Control ensures the users is able to operate the tool at the same speed that you would operate the tool on a full charged battery, even when the remaining battery capacity becomes low.
• One Touch Bit Installation - new bit installation has been designed to prevent the bit from unexpectedly falling off. A more effective mechanism has been designed increasing the strength of the chuck without increasing the resistance required to install a bit.
• 6 Optimised Application Modes - 6 assist mode variations; T-mode 1 and 2 for self-drilling screws in both thick and thin sheet metal. Wood mode for fastening long wood screws. Bolt modes 1 to 3 with rotation auto stop for tightening / loosening bolts.
• 4 Speed Power Selection - 4 electronic speeds allow the user to adjust the power, speed and impact rate to suit the fastening application.
• High Power Output - the high power 40Vmax XGT Li-Ion battery allows for continuous operation in heavy duty applications such as metal fastening screws or coach bolts.

Makita 40V Max 125mm (5") Angle Grinder, Slide Switch GA005GZ

Features:

• Switch Design - features the slide switch design. The grip circumference has been reduced for more comfortable handling.
• Active Feedback Sensing Technology (AFT) - sensors shut down the tool in the event of a kickback providing user protection. If the wheel rotation is suddenly forced to stop such as the wheel jamming the motor automatically shuts down.
• Tool less Wheel Cover allows for fast and easy adjustment and installation / removal of wheel cover, for swapping to optional cutting or dust collection guards.
• High Power Output - the high power 40 V max XGT Li-Ion battery allows for continuous operation in heavy duty applications. Maximum power output is 40% higher than the 18V equivalent.
• High Durability - advanced protection against heat and dust ensure the tool can run for longer in heavy duty applications without overheating. Whiles improvements have also been made to bearing and switch components to ensure long term durability
• Electric Brake maximises productivity and user safety by rapidly slowing the wheel rotation after the switch has been released.
• Soft Start / Anti Restart - wheel starts slowly then rapidly accelerates to maximum speed to reduce the initial start up shock. Anti restart restricts the tool from starting if the trigger is depressed when a battery is installed.

Makita 40V Max Recipro Saw JR001GZ

Features:

• Blade Ejection Lever - relocated to the side of the housing for increased convenience in removing the blade. The users hands no longer need to go near the blade for removal.
• Electric Brake - maximises productivity and user safety by rapidly slowing the blade speed after the switch has been released.
• Tool less Shoe Adjustment - quickly and easily adjusted to suit the dimension of the material being cut without the need for additional tools.
• Electronic 2 Speed - slide switch allows for selection between high and low speed. High speed has been designed for wood cutting while low speed for metal cutting.
• High Durability - advanced durability protection ensure the tool can run for longer in heavy duty applications. Whiles improvements have also been made to slider mechanism and gear shaft components to ensure long term durability.
• Rubber Joint Construction - the tool body is separated into the upper and lower housings at the foot of handle portion where the housing is connected with vibration absorbing cushion rubbers. This prevents the battery terminal from chattering or the battery rails from being worn out.
• High Power Output - the high power 40 V max XGT Li Ion battery allows for continuous operation in heavy duty applications. Maximum cutting speed on the JR001G is 35% faster than the 18V equivalent.

Makita 40V Max 28mm Rotary Hammer (AWS Compatible) HR001GZ

Features:

• Chuck Type - Rotary hammer is equipped with a standard chuck compatible with SDS Plus bits.
• Improved Tool Balance - improved design optimises the tool's center of gravity locating it as close to the handle grip as possible. This provides ideal weight distribution for more control and less fatigue even in overhead or horizontal drilling/chipping applications.
• Anti Vibration Technology (AVT) - extremely low vibration is achieved by 4 active vibration absorbing mechanisms. A counterweight, vibration absorbing rear handle, anti vibration side grip and rubber joint construction.
• Auto Start Wireless System (AWS)* - compatible with AWS the rotary hammer can be paired with a compatible vacuum for on demand dust extraction. AWS uses Bluetooth to wirelessly power on and off the extraction unit using the tools trigger. (*AWS receiver sold separately)
• Variable Speed Trigger & Dial - impacting power can be adjusted by switch trigger and speed dial according to applications.
• Active Feedback Sensing Technology (AFT) sensors shut down the tool in the event of a kickback providing user protection. If the bit rotation is suddenly forced to stop such as the bit jamming the motor automatically shuts down.
• High Power Output - the high power 40 V max XGT Li-Ion battery allows for continuous operation in heavy duty applications. Such as drilling with a 65 mm diamond core bit.

Makita 40V Max 185mm (7-1/4") Circular Saw (AWS Compatible) (tool only) HS003GZ

Features:

• High Power Output the high power 40 V max XGT Li Ion battery allows for continuous operation in heavy duty applications. With cutting speeds faster than the AC equivalent.
• Lightweight Design - battery relocation has significantly improved the overall balance creating a lightweight design that is extremely comfortable to use.
• Soft Start - blade starts slowly then rapidly accelerates to maximum speed to reduce the initial start up shock.
• Auto Start Wireless System (AWS)* - compatible with AWS the HS003G can be paired with a compatible vacuum for on demand dust extraction. AWS uses Bluetooth to wirelessly power on and off the extraction unit using the tools trigger (*AWS receiver sold separately).
• Automatic torque Drive Technology (ADT) - automatically gives optimal rpm to torque ratio to produce the fastest cut in light or hard applications.
• Positive Bevel Stop - allows for fast and accurate bevel adjustment to common bevel angles. With a maximum bevel capacity of 0-56°, positive stops at 22.5° and 45°.
• Electric Brake maximises productivity and user safety by rapidly slowing the wheel rotation after the switch has been released.

Makita 40V Max 4.0Ah Battery (BL4040) 191B26-6

Features:

• Built tough - High durability features specifically designed for XGT
• Shock absorbing structure
• High Rigidity Battery Rails - Durable slide in battery rail holds the battery and tools firmly to withstand high powered products
• Terminal shot-circuit prevention structure - The protection wall is positioned between terminals to protect them from water and dust
• Triple-layer Waterproof Structure - Prevents cell failure due to water and dust

Makita 40V Max Rapid Charger (DC40RA) 191E09-4

Features:

• Optimum Charging System - Rapid optimum charge is achieved by feeding real time data of the battery being charged with the charging control system . Data such as battery condition and cell temperature are communicated to optimise the charge
• Dual cooling fans - One for the battery and one for the charging circuit. This enable the charger to fully charge all batteries in the same charging time without slowing down due to a heat increase
• New charging status indicator light - The enlarged and raised LED light provides clearer indication of charging status.
• Compatible with LXT Li-Ion Batteries - ADP10 was developed for use with the DC40RA to rapid charge 18V batteries faster then ever before