Enerdrive 200Ah B-TEC Battery Bundle with DC40 Charger, AC60 & EPRO+
1x K-200-DC-BUNDLE Enerdrive ePOWER B-TEC 200Ah Lithium Battery
1x EN3DC40+ Enerdrive ePOWER 12V 40A DC to DC Battery Charger
1x EN31260 Enerdrive ePOWER 12V 60A Battery Charger
1x EN55050 Enerdrive ePRO PLUS Battery Monitor
Enerdrive B-TEC 12V 200Ah G2 Lithium Battery
Available in 12v 100Ah, 125Ah, 200Ah and 300Ah capacities and 24v 100Ah & 36v 100Ah, the ePOWER B-TEC lithium battery is designed and intended for use in deep cycle applications where a single battery is required that meets the amp hour capacity.
Smart Phone Monitoring System
The Enerdrive B-TEC G2 battery incorporates wireless Battery Monitoring Technology. By downloading the Android™ or Apple® app to your smartphone or tablet device, you can monitor the following information;
- Battery Capacity
- Battery Voltage
- Battery Current (Amps)
- Battery State of Charge (SOC)
- Battery State of Health (SOH)
- Battery Status
- Individual Cell Voltage
- Battery Temperature
- Battery Cycles
- Battery Alarms
- Battery Event Information
Battery Management System
The battery is also equipped with an internal Battery Management System that can monitor and optimise each Prismatic cell within the battery during normal operation. It will protect the battery pack from over charge, over discharge, over temperature & short circuit. The BMS helps to ensure safe and accurate operation of the battery.
Size & Weight Savings
Lithium v AGM Capacities;
- 100Ah Lithium = 160Ah AGM
- 125Ah Lithium = 200Ah AGM
- 200Ah Lithium G2 = 320Ah AGM
(Based on standard depth of discharge for both Lithium (80%) and AGM (50%).
The Enerdrive B-TEC G2 battery provides 60% more usable power than its equivalent lead acid cousin and being nearly 50% lighter and 30% smaller makes for a superior alternative.
The Enerdrive B-TEC G2 battery is perfect for camper trailers, 4WD’s (AUX battery), caravans, small water craft, low power communication sites or any other application that requires the use of a single deep cycle battery that meets the amp hour capacity.
The New Generation 2 B-TEC
So, How does the New Enerdrive Generation 2 (G2) B-TEC 200Ah Lithium Battery measure up against it original predecessor? Let’s have a look.
The increase in height allows for full 360° connection of the battery cables the make installation easier and more flexible. Also included for free is a metal battery tray and hold down strap to complete the installation process.
The G2 now incorporates a “Built-In Reset Button” making re-starting a flat battery a breeze. No longer do you need to apply a voltage to the battery terminals to wake up the battery. Press the button and within seconds, the battery will come back to life ready to accept a charge source to rejuvenate the battery.
The new G2 also includes a RS485 communications port located on the top of the battery. This port allows for integration onto other CanBus systems for data monitoring and recording.
The New Enerdrive Generation 2 (G2) B-TEC 200Ah Lithium Battery now comes with a 5 year Manufacturer Warranty, giving you peace of mind that this product will keep you covered.
With over 7 years of researching, designing and testing lithium batteries and the associated charging systems, Enerdrive are at the forefront of lithium battery systems in Australia. Enerdrive are the only Australian company that can supply a fully integrated self-branded energy system to suit your setup.
With over 3000 complete systems in operation Australia wide, Enerdrive is regarded as the leader in the field of lithium batteries and energy systems for Mobile, Marine and Remote applications.
Please Note; The G2 battery is capable to be paralleled to a second G2 battery. For maximum performance and lifespan of your G2 battery, no more than 2 batteries should be connected together to increase your overall capacity. Overall loads when paralleled should not exceed the current limits of a single batteries BMS.
The G2 200Ah battery is able to accept a maximum inverter capacity of 2600W only. Exceeding the maximum inverter capacity can damage the BMS Management within the battery.
If you are requiring a battery system larger than the Enerdrive B-TEC G2 battery, please look at the Enerdrive Pro Series Power Pack Systems which can offer multiple parallel and series connections with Active Cell Balancing Protection across the entire pack.
|Normal Specification||EPL-100BT-12V-SLIM||EPL-125BT-12V G2||EPL-200BT-12V G2||EPL-300BT-12V G2|
|Cycle Life (DOD – 80% under controlled conditions)||≥ 2000 Cycles|
|Standard Charge Specification (Lithium profile charger required)|
|Battery Charge Temperature||0 ̴ 45°C|
|Normal Charge Voltage CV/CC*||14.20 ̴ 14.60V|
|Standby (Float) Voltage||13.50 ̴ 13.80V|
|Maximum Charge Current||80A @ 25˚C for 30mins||60A @ 25°C for 30mins||150A @ 25°C for 30mins||190A @ 25°C for 30mins|
|Recommended Charge Current
For Maximum Life, Charge in the lower amperage range
|Standard Discharge Specification|
|Battery Discharge Temperature||-20 ̴ 60°C|
|Battery Output Voltage Range||11.00 ̴ 14.60V|
|Maximum Discharge/Pulse Current||100A @ 25˚C ±5˚C for 30 mins||100A @ 25˚C ±5˚C for 30 mins||200A @ 25˚C ±5˚C for 30 mins||250A @ 25˚C ±5˚C for 15 mins|
|Pulse Discharge Current||250A for 1.0s||450A for 1.0s|
|Discharge Cut-off Voltage||≤11.20V|
|Circuit Protection||The battery is supplied with a LiFePO4 Battery Management System BMS that can monitor and optimize each single prismatic cell during charge & discharge, to protect the battery pack from overcharge, over discharge & short circuit. Overall, the BMS helps to ensure safe and accurate operation of the battery.|
|Over-charge Protection Per Cell||3.90V ± 0.03V|
|Over-charge Release Per Cell||3.60V ± 0.05V|
|Over-charge Release Method||Discharge below release voltage|
|Over-discharge Protection Per Cell||2.80V ± 0.05V|
|Over-discharge Release Per Cell||3.20V ± 0.05V|
|Over-discharge Release Method||Apply Charge/Voltage ≥12.8V|
|Battery Manual Reset Button||No||Yes|
|Over Current Protection|
|Discharge Over Current||110A for 30s – 450A for 1s||110A for 30s – 450A for 1s||220A for 30s – 450A for 1s||280A for 25s – 400A for 3.5s|
|Protection Reset Time||Approx 10s Auto Release|
|Over Current Release Method||Disconnect Load|
|Over Temperature Protection|
|Battery Discharge Over Temperature||Protection to 65°C ± 5°C|
|Release at 50°C ± 5°C|
|Battery Charge Over Temperature||Protection to 55°C ± 5°C|
|Release at 45°C ± 5°C|
|Short Circuit Protection||Auto release after 5s|
|Weight||Approx 12.5 Kg||Approx 15.5 Kg||Approx 25.0 Kg||Approx 38.2 Kg|
|Temperature & Humidity Range||≤ 30 days -20°C ̴ 60°C, 5 ̴ 75% RH|
|≥ 90 days -10°C ̴ 45°C, 5 ̴ 75% RH|
|Self-discharge Rate||≤ 3% Per Month|
Note: Specifications subject to change without notice.
12V 40A DC2DC+ Battery Charger
- Two totally independent DC Inputs for both engine and solar regulation charging one house battery bank output
- DC M6 screw terminals that will allow for large battery cable connection between all sources
- A dedicated Maximum Power Point (MPPT) solar regulator
- The same battery algorithms as included in our AC mains ePOWER battery charger. GEL, AGM, Flooded, Lithium and the ability to create a full custom profile
- Vehicle input allows for either 12 or 24v and a maximum solar input of 45V/800W
- 40A+ output up to 40+°C with thermo controlled fan cooling
- Fully programmable LCD display to show which source is charging the battery along with charger status, voltage and amperage
- Temperature sensor included with charger for more accurate battery charging
The Enerdrive ePOWER DC2DC+ Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller. With two inputs available, the main/house battery will be charged from either the engine while underway, or via the solar panels when stationary. The process to choose either engine or solar is fully automatic and both functions are controlled from within the unit itself without the need for external relays.
During normal operation the ePOWER DC2DC+ Battery Charger will do a full charge cycle to float stage on the house battery bank with ability to choose either GEL, AGM, Flooded, Custom Programmable or Lithium. Once float stage is reached the charger transitions to a power supply mode to support any on-board DC loads.
Multistage Charging Process
The ePOWER DC2DC+ Battery Charger is a fully automatic, set and forget charger. It is designed to quickly and accurately recharge your deep cycle batteries utilising charger algorithms that help to maximise the life of your specialised deep cycle batteries.
The ePOWER DC2DC+ Battery Charger features multistage smart charging technology that enables the charger to be connected to your battery bank permanently. With the input of multiple sources, you can be assured of charging your batteries whenever underway; or when the sun is shining on your solar array.
As dictated by battery manufacturer’s recommendations, deep cycle batteries require a multistage charge sequence for perfect, fast and accurate charging. The Enerdrive ePOWER DC2DC+ smart charger delivers three primary charge stages.
Stage 1 – Bulk or Boost charge; The battery is charged at full rated output current of the charger until the battery reaches its final charging voltage, known as its absorption voltage. In this step, around 80% of the battery is recovered as fast as possible.
Stage 2 – Absorption Charge; With the charger voltage held steady, the remaining 20% is replaced with the charger allowing the current to taper off as the battery approaches full charge.
Stage 3 – Float; Finally, in the float stage the charger voltage is lowered and held at a constant and safe predetermined level. This prevents the battery from being overcharged, yet allows the charger to supply enough current to make up for the self-discharge losses of the battery, while supporting any additional loads connected to the battery (such as DC lighting and refrigerators). This stage allows for the charger to be used as a DC power supply.
Smart Charging Feature
The ePOWER DC2DC+ Battery Charger will regulate its output based on the loads connected to your battery bank. This function is important to maintain the life of your battery bank as some battery chargers mistake loads for discharge and continue to keep the batteries in the bulk or absorption stage for extended periods of time, which will damage the battery bank. The ePOWER DC2DC+ Battery Charger has two methods of load based regulation to ensure your battery charger transitions to float when it should do so.
DC2DC+ Battery Charger
|Output Voltage||12V Nominal (8.0V min)|
|Output Current (Maximum)||40A ~ 50A|
|Charger DC Output (CH1):|
|Selectable Battery Type||Gel, AGM, Flooded, Lithium, Program|
|Charger Voltage Range||13.8V – 15.5V|
|Float Voltage Range||13.0V – 13.8V|
|Charger Current (User Selectable)||5/10/15/20/25/30/35/40/45/50A (default 40A)|
|Equalize Voltage (Flooded Battery)||15.5V|
|Equalize Charging Current||10% of Bulk Current Setting|
|Charging Control||2 stage / 3 stage selectable (Default 3 stage)|
|DC Output Bank||Single|
|Current draw from CH1 when not in use||< 50mA|
|Battery Temperature Setting||Low/ Normal/ High (Battery Temperature Sensor Standard)|
|INPUT Rating (CH2 – MPPT Solar)|
|Input Voltage||14.5 – 45VOC|
|Maximum Input||≤ 23V input, 500W (600W allowable) ≥37.5V-45V input, 750W (800W allowable)|
|INPUT Rating (CH3 – Start/Alternator)|
|Input Voltage||10.5 – 16VDC / 21 – 32VDC|
|Height x Width x Depth||242mm x 172mm x 74mm|
|Unit Weight||1.85 Kg|
|Shipping Weight||2.17 kg|
Note: Specifications subject to change without notice.
Maximising your Solar Harvest using the DC2DC+
The Solar Input on the DC2DC+ unit has a maximum rated INPUT current of 30amps. This means it is optimised for using higher voltage ‘grid’ type modules for best output performance. The maximum achievable output using standard 20Voc solar modules will be approx 35amps @ 14.4Vdc
|Panel Array||Rated Wattage & Volts||Open Circuit rating||Estimated DC Amps Output (## See Below)|
|1||150watt @ 20Voc||150watts||10|
|1||200watt @ 43Voc||200watts||13|
|2||150watt @ 20Voc||300watts||21|
|2||200watt @ 43Voc||400watts||27|
|3||150watt @ 20Voc||450watts||31|
|3||200watt @ 43Voc||600watts||42|
|4||150watt @ 20Voc||600watts||35*|
|4||200watt @ 43Voc||800watts||47**|
|5||150watt @ 20Voc||1000watts||Not Recommended|
|5||200watt @ 43Voc||1000watts||Not Recommended|
* Maximum achievable output on the DC2DC+ unit when using 20Voc Solar Panels will be the approx 35amps. ** Maximum achievable output on the DC2DC+ unit when using 43Voc Solar Panels will be the approx 47amps.
## IMPORTANT NOTE: Estimated Amps Output is quoted based upon PERFECT Solar conditions including Sun Angle, Panel Mounting angle and Orientation to the sun. It needs to be noted that panel performance alters dramatically between Summer and Winter periods and actual performance may be impossible to predict.
ePOWER 12V 60A Battery Charger
- Multistage Charging: Fully automatic multistage battery charger with the ability to charge 3 separate battery banks.
- Separate Battery Banks: Isolated charging design where battery bank one is separate from battery bank two and three.
- Programmable: Battery bank 1 can be programmed with a different charge algorithm over banks 2 and 3.
- Current Control: User adjustable current output (e.g. Dial the 60amp unit back to run off a 1kVA generator).
- Smart Charging: The ePOWER 60A battery charger will regulate its output based on the loads connected to your battery banks.
- Wide AC Input Range: Operates on both 110V / 60Hz and 240V / 50Hz.
- LED Display: Easy to use “set and select” menu along with scrolling charger status.
- Silent Mode: Disables the cooling fan for total silent operation at night or whenever required. Activation reduces charge output by half and locks out fan for 12 hours.
- Temperature Sensor: Battery temperature sensor included with 3 meter cable.
- 5 Year Manufacturer Warranty from an Australian company renowned for customer support.
Multistage Charging Process
The Enerdrive ePOWER 60A Battery Charger is a fully automatic, “set and forget” charger. It is designed to quickly and accurately recharge your batteries using algorithms that help maximise service life. Multistage smart charging technology enables the charger to be connected to your battery banks permanently.
As dictated by battery manufacturer’s recommendations, batteries require a multistage charge sequence for perfect, fast and accurate charging. Our ePOWER multistage smart 60A battery charger delivers four primary charge stages:-
- Stage 1 – Bulk or Boost Charge; The battery is charged at full rated output current of the charger until the battery reaches its final charging voltage, known as its absorption voltage. In this step, around 80% of the battery capacity is recovered as fast as possible.
- Stage 2 – Absorption Charge; With the charger voltage held steady the remaining 20% is replaced allowing the current to drop as the battery approaches its full charge.
- Stage 3 – Float; Finally, in the float stage the charger voltage is lowered and held at a constant and safe predetermined level. This prevents the battery from being overcharged while supporting any additional loads connected to the battery, such as DC lighting and refrigerators. This stage allows for the charger to be used as a DC power supply.
- Stage 4 – Maintenance; This stage is a regular timed “return to bulk” stage. After 7 days of constant operation in “float” the Enerdrive ePOWER Battery Charger will switch the charger from float to bulk to agitate the batteries electrolyte helping to provide an extended service life.
1 PRIORITY – Charge Where You Need it Most
The ePOWER 60A Battery Charger delivers a priority charge to Bank 1, or your main house battery bank which allows the charger to get this bank recharged the quickest, then transition the cycle to the lesser bank 2 & 3 batteries.
The priority function also allows you to have a battery chemistry different to the other two, such as an AGM battery for house and lead calcium for your start banks.
In the event that all 3 banks are in need of a charge, an over-ride function helps recover all 3 banks quickly and evenly before switching back to prioritise on Bank 1.
All About Lithium
The recent advances in high capacity Lithium battery technology have seen the need to develop a battery charger suited to their needs. With most traditional ‘smart’ chargers their suitability to Lithium batteries is limited. Lithium batteries require a constant current / constant voltage charge algorithm and are unique in that almost every amp-hour of charge delivered by the charger is accepted as one amp hour into the battery, hence the need to deliver a constant current as long as possible.
The Enerdrive ePOWER charger can be programmed for Lithium batteries. This setting delivers the full rated output of the charger constantly with the charger switching to power supply mode once the voltage peak is met (indicating a full battery bank). The graph shows the ePOWER charger algorithm perfectly supporting Lithium battery requirements.
The Display Panel
The ePOWER 60A Battery Charger display gives you all the information you need for the operation of your charger. At a glance, key information such as charger amps, battery voltage and charge state continually alternate on the screen.When in float / power supply mode, the load amps are displayed so you can see exactly what the charger is doing. The display also allows you to program all settings of the charger, as well as activate the silent mode.
Silence when you need it – By pressing the “SEL” button for 5 seconds, the ePOWER Charger enters the ‘Silent’ mode that prohibits the fan from working. This ensures totally silent and safe operation at night, ideal if the charger is located close to your sleeping quarters. Silent mode limits current output to no more than 50%, and is programmed to remain on for 12 hours before automatically returning to a normal ‘fan-on & full output’ setting.
ePRO Plus Battery Monitor
ePRO PLUS High Precision Battery Monitor
The ePRO PLUS is our latest generation, highly advanced battery monitor. It consists of an intelligent shunt and a remote control display unit. The shunt has a Grid Optimized footprint for perfect integration with our DC Modular products.
This advanced battery monitor not only shows the true state of charge of your battery system. It also offers a large amount of additional features to optimally supervise your battery system and control external equipment. The ePRO PLUS is compatible with lead based and Lithium batteries (LiFePO4).
The ePRO PLUS can monitor up to three battery banks. The inputs for battery bank 2 and 3 can also be configured for other purposes, like mid-point voltage measurement, keyswitch input, setup lock or backlight control. The ePRO PLUS battery monitor can measure DC currents up to 600Amps (500Amp continuous) and voltages up to 70Vdc. So any lead- or lithium based battery from 12V up to 48V can be monitored.
The installation time is minimal, requiring only one supply wire to the intelligent shunt base and a single ‘QuickLink’ cable between the shunt base and the control/display unit (CDU). Additionally, the battery minus cable must be interrupted in order to insert the shunt into the high current circuit. The fused supply wire and the QuickLink cable are both included in the package, avoiding the need for a separate connection kit.
|ePRO Plus (Part No: EN55050)|
|Supply voltage range||7..70Vdc|
|Supply current (@ 12V/ 24V/48V)||10mA / 6mA / 5mA|
|Input voltage range main battery (+B1)||7..70Vdc1)|
|Input voltage range second & third battery (+B2, +B3)||1..70Vdc|
|Input current range||-600..+600A2)|
|Battery capacity range||10..10000Ah|
|Operating temperature range||-20..+50°C|
|Storage temperature range||-30..+70°C|
|Voltage (0..70V)||± 0.01V|
|Current (0..10A)||± 0.01A|
|Current (10..100A)||± 0.1A|
|Current (100..600A)||± 1A|
|State of Charge (0..100%)||± 1%|
|Time remaining (0..24hrs)||± 1min|
|Time remaining (24..240hrs)||± 1hr|
|Amphours (0..10000Ah)||± 0.01Ah..10Ah (variable)|
|Power (0..42kW)||± 0.01W..1kW (variable)|
|Temperature (-20°C..+50°C)||± 0.5°C|
|Voltage measurement accuracy||± 0.3%|
|Current measurement accuracy||± 0.4%|
|Footprint||100 x 100mm|
|Front panel||Ø 64.0mm|
|Body diameter||Ø 51.5mm|
|Protection class||IP20 (CDU front panel only IP65)|
|Standards||CE certified (EMC Directive 2014/30/EU) including EN50498 Automotive EMC|
|ePRO Plus 2ch Alarm Output Expander Kit EN5093120|
|Communication bus type||ePRO Plus QuickLink|
|Current consumption||< 1mA|
|Relay A and B contact ratings||8A / 250Vac or 8A / 30Vdc|
|Relay A and B dielectric strength||4000Vac (1min.) between coil and contacts|
|Relay pulse time (contactor mode)||approx. 750ms|
|Operating ambient temp||-20 ... +50 °C|
|Dimensions (L x W x H)||100 x 100 x 24mm|
|Type||Lithium Ion Battery|